1. Water supply system:
Water source problem:
Water source pressure fluctuation: If the pressure of the external water supply to the Automatic dripping machine is unstable, sometimes high and sometimes low, then the pressure of the Automatic dripping machine will also fluctuate. For example, when the municipal water supply system has different pressures during peak and trough periods, and the Automatic dripping machine is directly connected to the municipal water supply, this situation is prone to occur.
Insufficient water source: The water level in the water tank or other water supply container is too low, resulting in insufficient water supply, which will make the amount of water sucked by the Automatic dripping machine unstable, and thus the pressure unstable. For example, the water inlet valve of the water tank fails and cannot replenish water in time. As the drip machine works, the water level in the water tank gradually decreases, and the pressure will also decrease.
Water pump failure:
Water pump impeller wear: After long-term use, the water pump impeller may wear, resulting in uneven centrifugal force generated when it rotates, which in turn affects the output pressure of the water pump and makes the pressure unstable. For example, the impeller blades become thinner and deformed, and the gap between the impeller and the pump casing increases, which will cause pressure fluctuations.
Abnormal pump speed: Failure of the motor driving the water pump, such as motor aging, unstable voltage, etc., may cause the pump speed to be unstable, thereby making the water supply pressure unstable. For example, when the motor supply voltage is lower than the rated voltage, the motor speed will drop and the output pressure of the water pump will also drop.
Water pump blockage: impurities and dirt in the water may block the water inlet or impeller of the water pump, hindering the normal flow of water and causing unstable pressure. For example, in some environments with poor water quality, mud and debris in the water can easily enter the water pump and accumulate around the impeller, affecting the performance of the water pump.
2. Pipeline system:
Pipeline blockage: The inside of the pipe of the Automatic dripping machine may gradually become blocked due to the precipitation of impurities and the accumulation of scale in the water. Pipeline blockage will increase the resistance of water flow and reduce pressure. For example, in areas where hard water is used for a long time, calcium, magnesium and other ions in the water are easy to form scale on the inner wall of the pipe. Over time, the scale will become thicker and thicker, resulting in a smaller inner diameter of the pipe, poor water flow and reduced pressure.
Pipeline leakage: If the connection part of the pipeline is not sealed tightly, or the pipeline itself is damaged or cracked, water leakage will occur. Water leakage will cause the pressure in the system to decrease, and the pressure will fluctuate due to the unstable amount of water leakage. For example, if the joint of the pipeline is loose, or the pipeline is squeezed by external force, corroded and ruptured, it will cause unstable pressure.
Unreasonable pipe diameter: If the pipe diameter of the pipeline is not selected properly, it is too thin or too thick, which will also affect the pressure of the water flow. A pipe diameter that is too thin will increase the resistance of the water flow and reduce the pressure; a pipe diameter that is too thick may cause the water flow speed to be too slow, unable to meet the working requirements of the dripping machine, and will also cause pressure fluctuations. For example, in some small Automatic dripping machines, if a pipe with a large diameter is used, the water flow speed will be uneven and the pressure will be unstable.
3. Control and regulation system:
Pressure sensor failure: The pressure sensor is an important component for monitoring pressure in the Automatic dripping machine. If the pressure sensor fails, such as damage, reduced accuracy, etc., it cannot accurately measure the pressure, which will cause the control system to be unable to adjust according to the actual pressure, making the pressure unstable. For example, if the pressure sensor is subject to electromagnetic interference or the internal components are aged, the measured pressure value does not match the actual pressure, which will mislead the control system.
Controller failure: The controller of the Automatic dripping machine is responsible for controlling the operation of the water pump according to the signal of the pressure sensor to maintain a stable pressure. If the controller fails, such as program errors, damage to electronic components, etc., it will not be able to adjust the working state of the water pump normally, resulting in unstable pressure. For example, if there is a problem with the control algorithm of the controller and the speed of the water pump cannot be adjusted in time according to the pressure change, the pressure will fluctuate.
Regulating valve failure: The regulating valve is used to adjust the water flow in the pipeline to control the pressure. If the regulating valve fails, such as the valve core is blocked, the valve stem is deformed, etc., the water flow cannot be accurately adjusted, resulting in unstable pressure. For example, if the valve core of the regulating valve is stuck by impurities and cannot be fully opened or closed, the water flow will be unstable and the pressure will fluctuate accordingly.
4. Other factors:
Ambient temperature changes: Changes in ambient temperature may affect the density and viscosity of water, thereby affecting the pressure of the water flow. At low temperatures, the density and viscosity of water increase, the resistance to water flow increases, and the pressure may drop; at high temperatures, the density and viscosity of water decrease, the water flow rate may increase, and the pressure may also change. For example, in the cold winter, the pressure of the automatic dripper may be lower than in the summer.
Altitude effect: Changes in altitude will cause changes in atmospheric pressure, which in turn affects the working pressure of the automatic dripper. In areas with higher altitudes, the atmospheric pressure is lower and the boiling point of water is also lower, which may cause the pressure inside the automatic dripper to be relatively low. For example, when using an automatic dripper in plateau areas, the equipment needs to be properly adjusted according to the local altitude.
Equipment load changes: If the load of the irrigation or other working system connected to the automatic dripper changes, such as an increase in the irrigation area, an increase in the number of sprinklers, etc., the water demand will change, making the pressure of the automatic dripper unstable. For example, an automatic dripper originally designed for irrigation of 100 square meters may drop in pressure when the irrigation area is expanded to 200 square meters due to the increase in water flow demand.
What factors may cause the pressure of the Automatic dripping machine to be unstable?
Oct 14, 2024 Leave a message
Send Inquiry




