1. Preparation:
Determine the appropriate lubricating oil: According to the model, working conditions and manufacturer's recommendations of the rolling mill, select the appropriate lubricating oil. Ensure that the quality and performance of the lubricating oil meet the requirements to ensure the normal operation of the rolling mill.
Prepare tools and equipment: Prepare the tools required to change the lubricating oil, such as wrenches, drain plug wrenches, funnels, oil drums, etc. At the same time, ensure that there is a sufficient supply of new lubricating oil.
Safety measures: Before changing the lubricating oil, be sure to cut off the power supply of the rolling mill and take appropriate safety measures, such as hanging warning signs, etc. to prevent accidental start-up. In addition, appropriate personal protective equipment should be worn, such as gloves, goggles, etc.
2. Drain the old oil:
Find the drain port: Find the location of the drain port or drain plug on the rolling mill. Usually, the drain port is located at the bottom or side of the oil tank.
Place the oil drum: Place a suitable oil drum under the drain port to collect the old oil. Make sure the oil drum has enough capacity and is placed stably to prevent oil spills.
Open the oil drain port: Use a drain plug wrench or other appropriate tool to slowly open the oil drain port and let the old oil flow slowly into the oil barrel. Pay attention to control the speed of draining the oil to avoid splashing caused by too fast oil flow.
Empty the oil tank: Wait for the old oil to drain completely, which may take some time, especially if the oil tank is large or the oil viscosity is high. You can gently shake the mill or tilt the oil tank to help the old oil drain more thoroughly.
3. Clean the oil tank and filter:
Remove the oil tank cap: After the old oil is drained, remove the oil tank cap. Be careful to save the oil tank cap and related seals.
Clean the inside of the oil tank: Use a clean cloth or brush to thoroughly clean the oil, impurities and sediment inside the oil tank. Make sure the inside of the oil tank is clean and free of foreign matter.
Check the internal parts of the oil tank: Also check the parts inside the oil tank, such as the oil pump, oil pipe, filter, etc., for signs of damage or blockage. Repair or replace if necessary.
Clean or replace the filter: Find the lubricating oil filter of the rolling mill, remove it and clean or replace it. If the filter is very dirty or clogged, it may affect the flow and filtering effect of the lubricating oil, so it is recommended to replace the filter regularly.
4. Add new oil:
Prepare new oil: Make sure the quality and model of the new lubricating oil are consistent with the requirements of the rolling mill, and preheat it to the appropriate temperature before adding it to reduce the viscosity of the oil, facilitate filling and better fill the system. But be careful to avoid overheating and change the oil quality.
Use a funnel to fill: Insert the funnel into the oil tank filling port and slowly pour the new oil into the tank. Pay attention to control the speed of pouring oil to avoid too many bubbles. At the same time, monitor the rising oil level through the oil level indicator or dipstick on the oil tank to ensure that the amount of oil added meets the requirements.
Check the oil level: After adding a part of the new oil, stop filling and check whether the oil level has reached the appropriate position between the minimum and maximum marks. If the oil level is too low, it may cause insufficient lubrication; if the oil level is too high, it may cause oil leakage or other problems. Continue to add or adjust the oil level as needed.
5. Start the mill and check:
Reinstall the oil tank cap and related parts: After confirming that the oil level is appropriate, reinstall the oil tank cap and other related parts on the mill and ensure that the seal is good.
Connect the power supply and start the mill: According to the operating procedures of the mill, connect the power supply and start the mill. Let the mill run at low speed for a period of time so that the new oil can fully circulate to various lubrication parts, and check for abnormal noise, vibration or leakage.
Check the oil level and oil temperature again: After the mill has been running for a period of time, check the oil level and oil temperature again. The oil level should be kept within the appropriate range, and the oil temperature should also be within the normal operating temperature range. If any problems are found, the machine should be stopped immediately for inspection and troubleshooting.
6. Record and maintenance:
Record replacement information: Record the date, time, type and quantity of lubricant replacement for future reference and maintenance.
Regular inspection and maintenance: Establish a regular inspection and maintenance plan, including checking the oil level, oil temperature, filter condition, and the working condition of the lubrication system. According to the inspection results, necessary maintenance and care work should be carried out in a timely manner to ensure the long-term stable operation of the rolling mill.
How to change the lubricating oil of Horizontal Padding Mangle?
Oct 28, 2024 Leave a message
Send Inquiry




