Automatic dripping machine maintenance operation steps

1. Clean the equipment:
External cleaning: Wipe the body of the Automatic dripping machine regularly to remove dust, stains and debris. Use a clean and soft cloth, and avoid using rough or corrosive detergents to avoid scratching or damaging the surface of the equipment. For stubborn stains, you can use a mild detergent, but be careful to rinse it thoroughly.
Internal cleaning: Clean the internal parts regularly according to the use of the equipment. For example, water tanks, pipes, filters, etc. may accumulate dirt or impurities, affecting the dripping effect and equipment performance. According to the instructions of the equipment, disassemble and clean the relevant parts to ensure that the interior is clean.
2. Check the parts:
Regular inspection: Regularly check the various parts of the Automatic dripping machine, such as water tanks, pipes, valves, filters, needles or drip nozzles, to see if there are signs of damage, blockage or wear. Timely detection of problems and taking appropriate measures can avoid more serious failures.
Key inspection parts:
Water tank: Check whether the water tank has cracks, water leakage and other problems, and replace the water tank in time if necessary. At the same time, check whether the water level sensor of the water tank is working properly to ensure accurate water level control.
Pipeline: Check whether the pipeline is broken, deformed, blocked or leaking. If there is a problem with the pipeline, it should be repaired or replaced in time. In addition, it is necessary to check whether the connection part of the pipeline is loose. If it is loose, it should be tightened in time.
Valve: Check whether the valve is flexible to open and close and whether there is water leakage. If the valve fails, it should be repaired or replaced in time. At the same time, make sure that the operating handle or button of the valve is in the correct position.
Filter: Check whether the filter is blocked. If the filter is seriously blocked, it will affect the water quality and water flow rate. It should be replaced at the prescribed time interval or according to actual use.
Needle or drip nozzle: Check whether the needle or drip nozzle is blocked, deformed or worn. A blocked needle or drip nozzle will affect the uniformity and accuracy of dripping and should be replaced in time.
3. Replacement of parts:
Timely replacement: According to the inspection results, replace damaged or worn parts in time. For example, a clogged needle or drip nozzle will affect the uniformity and accuracy of dripping and should be replaced in time; an aged or broken pipe may cause water leakage and needs to be repaired or replaced in time; if the filter element of the filter is seriously clogged, it will affect the water quality and water flow rate and should be replaced at the prescribed time interval or according to actual use.
Replacement precautions:
Choose the right parts: When replacing parts, make sure to choose genuine parts that match the equipment model to ensure the performance and stability of the equipment.
Follow the instructions: Strictly follow the instructions of the equipment to replace the parts, pay attention to the installation sequence and method, and ensure that the parts are installed correctly.
Test run: After replacing the parts, perform a test run of the equipment to check whether the equipment is working properly and whether the dripping effect meets the requirements.
4. Maintain water quality:
Use a clean water source: Provide a clean, impurity-free water source for the Automatic dripping machine. If the water source has poor water quality, it may cause problems such as pipe blockage, shortened filter life, and poor dripping effect. Consider using filtered or purified water, or regularly treat and test the water source.
Regularly replace the water in the water tank: Avoid the growth of bacteria or algae due to long-term storage of water in the water tank. According to the frequency of use of the equipment and environmental conditions, regularly empty the water tank and replace it with new water. It is generally recommended to replace the water in the water tank once a week or every two weeks, and the specific time interval can be adjusted according to the actual situation.
Clean the water tank: When replacing the water in the water tank, clean the inside of the water tank at the same time. To remove dirt, scale and residual substances on the wall of the water tank, you can use a mild detergent and a soft cloth to wipe it, but be careful to rinse it thoroughly to avoid the residual detergent affecting the water quality.
5. Correct operation:
Follow the operating procedures: Before using the Automatic dripping machine, carefully read the instructions and operating guide of the equipment to understand the correct operating methods and precautions. Set, start, stop and adjust the dripping parameters according to the operating procedures to avoid equipment damage or performance degradation caused by misoperation.
Avoid overuse: Do not use the Automatic dripping machine for a long time continuously to avoid excessive fatigue and wear of the equipment. During the period when dripping is not required, the equipment can be properly turned off to let it rest and recover.
Pay attention to environmental conditions: Avoid using the Automatic dripping machine under harsh environmental conditions, such as high temperature, high humidity, strong corrosive gas or dusty environment. If it cannot be avoided, appropriate protective measures should be taken, such as installing ventilation equipment, using protective covers, etc., to reduce the impact of the environment on the equipment.
6. Regular calibration:
Regular calibration: Regularly calibrate the dripping parameters of the Automatic dripping machine, such as dripping volume, dripping speed, time control, etc., to ensure its accuracy and stability. You can use professional calibration tools or reference equipment for calibration, or contact the equipment manufacturer or professional maintenance personnel for calibration services. The calibration time interval can be determined according to the use and requirements of the equipment. It is generally recommended to calibrate once every six months or one year.
Calibration method:
Drip volume calibration: Use a measuring cylinder or other measuring tools to measure the dripping volume within a certain period of time and compare it with the dripping volume set by the equipment. If the dripping volume is inaccurate, you can calibrate it by adjusting the dripping speed of the equipment or replacing the dripping parts.
Drip speed calibration: Use a stopwatch or other timing tools to measure the dripping time interval and compare it with the dripping speed set by the equipment. If the dripping speed is inaccurate, you can calibrate it by adjusting the control parameters of the equipment or replacing the dripping parts.
Time control calibration: Use a clock or other timing tools to check whether the time control function of the equipment is accurate. If the time control is inaccurate, it can be calibrated by adjusting the clock setting of the device or replacing the control parts.
7. Storage and preservation:
Dry storage: When the Automatic dripping machine is not in use, it should be stored in a dry, ventilated place to avoid moisture, rust or corrosion. The device can be wiped clean to remove moisture and dirt on the surface, and then placed in a dry storage cabinet or packaging box.
Avoid collision and extrusion: When storing and carrying the Automatic dripping machine, be careful to avoid collision and extrusion to avoid damage to the housing, pipes or internal components of the device. Appropriate packaging materials and protective measures, such as foam pads, cartons, etc., can be used to protect the device.
Regular power-on operation: If the Automatic dripping machine is not used for a long time, it is recommended to power it on and run it once every period of time (such as about a month) to allow the device to perform self-test and preheating to maintain its performance and reliability. The running time can be determined according to the specific situation of the device. It is generally recommended to run it for a few minutes to more than ten minutes.